You’ve just bought a brand new Husqvarna 572XP chainsaw and you’re eager to start using it. You read the instruction manual and everything seems straightforward enough, but you soon start to experience some problems with your new saw.
Don’t worry, you’re not alone. Thousands of other Husqvarna 572XP owners have encountered the same issues. In this article, we’ll try to share some of the most common Husqvarna 572XP problems and their solutions. So, let’s get started with it.
Overview of Husqvarna 572XP
Before we get into the specific problems and solutions, let’s take a look at the Husqvarna 572XP in general. This is a gas-powered hedge trimmer that’s designed for heavy-duty use. It’s built for professionals who need a reliable piece of equipment that can handle some serious work.
The 572XP is powered by a 28cc two-stroke engine, which gives it plenty of power to cut through even the densest hedges. It also features an X-TORQ engine, which helps to reduce emissions and increase fuel efficiency. And last but not least, it comes with a Telescopic Handle that can be adjusted to fit any operator size.
Common Husqvarna 572XP Problems and Solutions
The Husqvarna 572XP is an incredible saw, but it has some drawbacks. Check out these Husqvarna 572XP problems and their solutions
1. Spark Plug Faulty
A spark plug is an essential component of a Husqvarna 572XP chainsaw, which helps the engine run properly and efficiently. If the spark plug becomes faulty, it can affect the performance of the chainsaw.
When a spark plug is faulty, the engine will not start or may have difficulty starting, poor performance, and poor fuel economy. The spark plug may also become fouled or damaged with debris and carbon deposits. This can cause the spark plug to misfire, leading to poor engine performance and decreased power.
There are a few things you can check to try to diagnose the problem. At first, make sure the spark plug is inserted correctly and that the electrodes are not corroded. If they are, you can either clean them or replace the spark plug.
You also need to make sure the compression is adequate. This can be done by removing the spark plug and holding a compression gage against the cylinder head while someone else cranks the engine over. The reading should be around 150 psi.
If both of those things check out, then you may have an air flow problem. This can be caused by a dirty air filter or a blocked exhaust pipe. Cleaning or replacing the air filter may solve the problem.
2. Compression Issues
The 572XP has a single-cylinder, two-stroke engine that operates at a relatively high RPM, which can lead to problems with compression. This can cause the engine to run rough and make it difficult to start or keep running. The compression issues can also lead to increased fuel consumption and reduce the overall performance of the saw.
To address the compression issues, it is recommended that the compression be tested regularly and the spark plug gap be adjusted if necessary. If the compression is still not up to par, then it may be necessary to replace the piston or piston rings. It is also important to use the proper fuel/oil mix for the 572XP and to make sure that the air filter is clean.
It is recommended that the muffler and the engine be checked for any signs of damage or wear. A damaged muffler or engine can contribute to compression issues, so it is important to address any issues as soon as possible.
3. Air Flow Problems
If you experience airflow problems with the Husqvarna 572XP, then it may be due to a blocked air filter. Check the air filter and replace it if necessary. If that doesn’t fix the problem, then you will likely need to adjust the carburetor setting or replace the carburetor. You should also make sure that the fuel line isn’t obstructed or leaking, and check for any loose hoses.
In some cases, a clogged muffler or spark arrester might be causing a blockage in the airflow system. Cleaning them out regularly can prevent this from happening. Additionally, check for any dust or debris inside the engine compartment and clean it out if necessary. This will help ensure that your saw runs smoothly and efficiently with good airflow.
4. Filled With Much Fuel
Have you ever filled up your Husqvarna 572XP with too much fuel? This is a common problem and one that not many people realize is preventable. The 572XP’s fuel tank will only take about two ounces of fuel, so it’s important to double-check how much is going in and make sure it’s not more than the recommended amount.
If the chainsaw does end up overflowing, it can cause oil to be left behind in the combustion chamber. This can cause the engine to work harder and reduce its efficiency and power output— leading to problems like excessive vibration and loss of power.
What should you do if this has already happened? The best thing to do is to empty out the fuel tank, then refill it with a fresh mixture of oil and gasoline. This should restore your chainsaw’s performance back to normal again. Make sure you don’t overfill it this time!
5. Fuel Supply Issues
Fuel supply issues can also plague the Husqvarna 572XP. If the fuel supply is not sufficient, it can cause a decrease in engine performance and power, If you are having difficulty starting and/or have low power, it could be due to a restricted fuel supply.
To diagnose this problem, start by checking the fuel filter. It may be clogged or blocked by debris. If so, clean the filter out or replace it with a new one if necessary. If that doesn’t do the trick, then check your fuel lines to make sure they aren’t obstructed or cracked. At last, inspect any valves that regulate fuel flow; they may be stuck or damaged and need to be replaced.
6. Faulty Ignition Coil
The ignition coil is an important part of the Husqvarna 572XP and any malfunction can lead to failure of the system. One of the common problems is faulty ignition coils which fail to provide enough energy for the spark plug to ignite the fuel and air mixture inside the cylinder.
This can be determined by checking for the spark in the spark plug. If there is no spark, replace the ignition coil. Another sign that your ignition coil might be faulty is if there is a noticeable drop in power and engine performance. To fix this issue, you need to replace the faulty ignition coil as soon as possible.
7. Excessive Vibration
If you’re experiencing excessive vibration while operating the Husqvarna 572XP chainsaw, it’s most likely caused by a loose bar. To fix this, make sure both screws on the side of the bar are tightened in place.
You can double-check that this is the cause of the problem by performing a simple test: Put your finger in front of the bar and try to push it forward or backward. If it moves too much or feels loose, then your screws are probably not tight enough and need tightening.
If that doesn’t solve the problem, check to see if the clutch cover is loose and tighten it if necessary. On most chainsaws, there are two screws located on each side of the cover which should be securely tightened. Once everything is tightened up, you should notice a huge difference in vibration levels!
8. Hard Starting
Having trouble getting your Husqvarna 572XP to start? There are a few potential causes for this issue. It could be that the spark plug is faulty and needs to be replaced, the air-fuel ratio is off, or the fuel supply is insufficient.
If your spark plug is worn out or dirty, it can cause the engine to be unable to start or run properly. Make sure you check your spark plug and replace it if necessary. Another potential issue could be too much fuel in the cylinders, which reduces the amount of oxygen available for combustion and causes hard starting.
To avoid this problem, make sure you drain any excess fuel that may have built up in the cylinder before starting your saw. You should also ensure that you have a sufficient fuel supply coming into the engine. If you suspect an insufficient fuel supply, check the fuel filter and replace it if necessary.
9. Loss of Power
If you’re experiencing a drop in power in your Husqvarna 572XP chainsaw, it could be due to several different issues. One possible cause is an air leak. Check the gaskets, fuel lines, and carburetor for any signs of air leakage. If any of them are loose or damaged, they might be allowing air to pass through and causing your chainsaw to lose power.
In some cases, the fuel tank might be clogged with debris. This can block the flow of fuel and cause a drop in power. If this is the case, clean out the fuel tank and check for any obstructions that could be blocking the fuel supply.
It’s also possible that your Husqvarna 572XP chainsaw is having compression issues due to a faulty spark plug or ignition coil. If either one of these components isn’t functioning correctly, it can prevent the motor from getting enough oxygen to burn fuel efficiently, leading to a decrease in power output.
How to Take Care of Husqvarna 572XP
You already got some ideas on Husqvarna 572XP problems and their solutions. Now you need to know how to maintain it. Maintaining your Husqvarna 572XP chainsaw will help ensure it lasts for years. Here are some tips to help you take care of your 572XP chainsaw and get the most out of it.
# Clean the air filter regularly
The air filter on the 572XP should be checked regularly and cleaned when necessary. A clogged or dirty air filter can reduce engine performance and cause damage to the internal parts of the machine.
# Use the proper fuel
The 572XP is designed to run on a high-octane gasoline and two-stroke oil mix. Always use fresh fuel and be sure to follow the mixing instructions in the manual.
# Perform regular maintenance
To ensure the best performance from your 572XP, it’s important to perform regular maintenance. This includes checking the chain tension, sharpening the chain, replacing the spark plug, and checking the condition of the fuel filter.
# Inspect the chain and bar
Regularly inspect the chain and bar to make sure they are in good shape. If the chain has worn down or has dulled, it can be sharpened or replaced. The bar should be inspected for damage and replaced if necessary.
# Store your 572XP properly
When not in use, it’s important to store your 572XP in a dry, cool environment. This will help prevent rust and corrosion and ensure that your chainsaw is ready to use when you need it.
# Follow the manufacturer’s instructions
Always read and follow the instructions in your manual before operating your 572XP. This will help ensure your safety and the safety of those around you. It’s also important to use the proper safety equipment, such as gloves, goggles, and ear protection.
By following these tips, you’ll be able to get the most out of your Husqvarna 572XP chainsaw and keep it running for years to come.
Final Thought
All in all, the Husqvarna 572XP is a great saw. However, as with any saw, there can be some common problems that may arise. But, don’t worry, we have compiled a list of some of the most common Husqvarna 572XP problems and their solutions.
So, if you’re having any issues with your 572XP, be sure to check out this list. It will surely help you all to know about those problems and their solutions as well.
